Skip to content

Follow us!

šŸšš Free Shipping for orders over $99 in Capitlal City Metro Areas šŸšš

šŸŒ± All our deliveries are carbon neutral šŸŒ±

Get in touch with us

INTERGRAIN - Matt - Ultraclear Exterior 10L Timber Finish

$212.00 $0.00
Unit price  per 
INTERGRAIN - Matt - Ultraclear Exterior 10L Timber Finish
Intergrain Logo Decking Supplies Online

INTERGRAIN - Ultraclear Exterior 10L Timber Finish - Matt

Intergrain UltraClear Exterior is a tough, clear, marine grade water based timber finish for use on window frames, doors and trims. Incorporating UV absorbers, UltraClear Exterior provides superior protection against the weather including the harmful effects of the sunā€™s UV radiation. Available in three different sheens, UltraClear Exterior has a low odour and unlike oil based coatings will not yellow. NOTE: Not suitable for walk on areas or broadwalls

  • WATER WASH UP
  • NON-YELLOWING
  • SUPERIOR PROTECTION AGAINST THE WEATHER

WHERE TO USE
Areas -Ā Doors, Window Frames, Trim. Not suitable for walk on areas or broadwalls
Substrates -Ā Cypress Pine, Jarrah, Merbau, Spotted Gum, Treated Pine, All exterior timber
Locations - Exterior

SURFACE PREP

New timber:
Sand timber to a uniform, smooth surface. Ensure the timber is dry and free from all dirt, dust, wax and oils. Clean oily timbers, such as Brushbox, Spotted Gum, Cypress or Tallowwood with methylated spirits and allow to dry. Note: Do not use steel wool on timber to be coated with UltraClear Exterior as severe staining will occur.

Grey and weathered with no previous coating:
Sand timber back to a fresh surface, and remove sanding dust. Note: The rounding of sharp edges with sandpaper is highly recommended to maintain coating film thickness.

Paints, varnishes or coatings in varied condition:
All paints and coatings that seal the surface must be thoroughly removed back to bare timber. To remove coating sand, or use a combination of Intergrain Liquid8ā„¢ Timber Stripper and sanding.

All composites & bamboo substrates:
Sand, remove sanding dust, then check for adhesion by applying UltraClear Exterior to a test area, approximately 250mm x 250mm. Allow to dry for twelve hours then firmly press a strip of sticky tape over the coated section and rip off quickly. If the coating is removed do not proceed as the surface is not suitable.

Important: If mould is present or if timber is in a mould prone area, use Intergrain UltraPrep Mould Killer to remove surface mould effectively as the first step of preparing the timber for coating

Nail holes and surface defects should be filled with Intergrain Woodblendā„¢ Wood Filler.

APPLICATION

Methods: brush, spray, Applicator

1. Stir thoroughly before and during use with a flat blade stirrer.
2. Apply three coats of UltraClear Exterior with a quality brush, pad applicator or spray.
FOUR or more coats will be required in extreme conditions such as full sun exposure, marine environments and in humid areas, and may be required on porous timbers.
3. Apply along the length of the board including exposed edges and end grain.
4. If necessary, sand lightly between coats to remove any raised grain.
5. Keep freshly coated contacting surfaces such as doors and windows ajar for several days if possible. Some tight closing windows may need sealing strips to prevent sticking.
6. Do not apply to hot surfaces or those in direct sunlight, as doing so may result in difficult application.
7. Do not apply in temperatures above 35Ā°C, below 10Ā°C or if rain or dew is expected within four hours of application. Lightly dampening timber before painting will ease application in temperatures
Note: UltraClearā„¢ Exterior is not suitable for heavy wear surfaces (such as decks and walkways), or for exterior broadwall such as cladding and weatherboard. For these areas use UltraDeckĀ® Timber Oil, UltraDeckĀ® Timber Stain, Natureā€™s TimberOilā„¢, or Heavy Duty.

MAINTENANCE

Conduct a routine 12 monthly maintenance inspection. Note: For marine environments conduct a 3 monthly maintenance inspection.

Best protection of the timber and ease of maintenance is ensured if UltraClear Exterior is recoated before deterioration of the coating and timber underneath occurs.

First indication of the need for recoating will be observed as patchiness or thinning of the surface coating on edges and areas where insufficient product has been applied.

If small areas of timber have weathered through to cause deterioration of the coating, sand affected areas back to bare timber, remove sanding dust and recoat.

For large weathered areas remove UltraClear Exterior by sanding, or use a combination of Liquid 8 Timber Stripper* and sanding.

To recoat UltraClear Exterior which is in good condition, lightly sand, remove sanding dust and apply one coat of UltraClear Exterior.


Customer Reviews

Based on 3 reviews Write a review

FAQ

live_help

Didn't find your answer?

Our customer service will be happy to help you.

How you can help

Whenever you purchse any of our products you are helping a small decking supply company go up against the big guys :)

How you can help

Yes, we are new and are building up our product offering. Let us know if we aren't stocking your favourite product and we will seriously look into each and every request.

How you can help

Share with your friends, let them know about our great service, range of products and great prices!